|
|
|
 |
 |
技术讲座 |
|
|
| |
LMCSS CONTRACT PARAMETER FOR AAA30085AAF
Installation Parameters (2-3-1)
Top floor _________----Enter top landing minus one
Bottom floor _________Lowest landing is always 0
Country AJG _________Enter 0 for NAA, 1=JAPAN,2=GERMANY
Enable ADO__________Set to a 1 to enable Advanced Door Open feature
DBSS parity OE____1_____Drive Dependent Prity Flag –
set to a 1
Car non start _____30__Length of time for a normal high speed run without seeing a DZ signal
Track err% NOR ______15______Set to 15 after Final adjustment
NTSD cutoff% _________ set to 60 initially ,reset during adjusting of NTSD
Upper Access Flr _______ Enter landing number of top access floor
ED car ID____0_____ set to elevator number in group for enhanced diagnostics,REM
Elev type _______enter 8 for GEM,9 for MVS & HVS
Dual ANSI SC brd _____0____
LSP Type ____0_____Can.B44:Enter “1” with rope grabber
Enter “2” with Gov. Trip soleniods Enter 0 for NAA operation
Ena CEN_HONGKONG _____0____ENTER 1 for CEN-HongKong controller
Ena pvt check ____2____
Track. Debnce cyc ____8____
MCSS to OCSS ICD _______0___ Enter 1 for B44 & DLF operation on NAA controllers after 8/1/97
Ena B44 DLF _______0____Enter 1 for B44 & DLF operation on NAA controllers after 8/1/97
ADV PTR option ____0___ HVS=10
Install2 (2-3-2)
Ena Dir Lim NY __0_____N=0,Y=1,Enable software direction limit
Rotate DIR NY______0___N=0,Y=1,Reverse PVT direction information from DBSS
Adv PTR Holdoff ___0_____Advanced prepare to run holdoff (100 ms),10-forgeared,0-for gearless
Wrt Prot Opt NY ____0____N=0,Y=1,Enable running the elevator with the write protect switch enable
Enable prejerk Vel_____0______ Not used on VF Drive
Prejerk Ramp Cyc ____7____
-----------------Dlt ____3______
DOOR COMM TYPE ____0_____DCSS(pnt –pnt)=0,Multidrop=1,Multidrop W/HPLIM=2注意HPLIM设为0
REM Enable _____0_____W/0 REM=0,W/REM=255(ENABLE/DISABLE)
REM Event Buffer _________0___ W/0 REM=0 W/REM=255(enable/unable)
REM Tim Event Ln ___5______ # of 100msec cycles
REM BAUD Rate _____48____ 4800 baud (only)
REM Msg Sumcheck _____255___ W/0 REM =0,W/REM=255(enable/disable)
Profile generator(2-3-3)
Velocity normal __________ Enter contract speed in mm/s
Accelera Normal _____ Enter 600 for all GEM & MVS 5035 duty :1000 for all other MVS/HVS duties
Jerk Normal ___1560____
*
Velocity Inspect _____350____
*Accelera Inspect ___600___
*Velocity Learn ____150____
*Accelera Learn __600____
Velocity Relevel __60____
*Accelera Relevel _____300____
Velocity Recover _250_
*Accelera Recover ___600____
*Velocity Slow ____150____
Velocity Reinit _____900___
Accelera Reinit ________Enter 600 for all GEM & MVS 5035 duties 1200 for all other MVS/HVS duties
Accelera NTSD ___________Enter 800 for GEM & MVS 5035 duties 1200 for all other MVS/HVS duties
NTSD Comp Distance ________Enter 200 for 1016 mm/s contract speed
Jerk timed __0_____
Velocity reduced ____700_____
Accelera reduced __600______
Jerk reduced ___600_____
Velocity profile 2 _1000____
Accel profile 2 _____600______
Jerk profile 2 ____1560_____
Velocity profile 3 __1000______
Accel profile 3 __600____
Jerk profile 3 ___1560____
Velocity test __1000_____
Acceleration test _600____
Jerk test ____1560______
Velocity zero ___1____
JPSDO type ____0______
Velocity JPSDO_____0____
*Gain fixed posct ______25_____
*Delta TC ___240____Minimum setting for VF drive
Decel/accel % _____100______
Destination Lead _____0____
Destination Lag______0______
Level tolerance __3_____
Zero speed time ____500____
BKL to Mov time ___0__
EOR PTR time ___0____Without Brake swicth,set to 5
Relevel delay_____50_____
CAB HEIGHT _2500____Set distance in mm to stop car with cross-head level with tp access ldg.level.
Bot ACCESS LEN ___2500____Set distance in mm,when set to 65535,bottom access length is set to full length of hoistway.
Position displmt ____0______
1LS/2LS tolerance _____300____
Slippage tolerance _200_____
Counts per revol ____________Enter 1024 for MVS/GEM 10000 for HVS
Motor speed _______See following table;enter motor rpm
HVS Gearless-156 MST Machine 24” drive sheave *
Contract Velocity
Motor RPM
2540 mm/s(500 fpm)
159
For other arrangements see formula on page 30 to calculate the “
Motor RPM”.
*Motor Base speed ________set to 80% of contract speed mm/s.
*Velocity Access __250_____Velocity for access operation in mm/s
*Prejerk Pos Delt _____0______Stiction Comp. PVT counts before motion (not used on VF Drive).
Landing Assignments (2-3-5)
Enter a”1” under the column for the appropriate door at each landing
Load Weighing parameters (2-3-6)
Load device type ____4_____
OCSS load enable ___1______
DBSS load enable _______1_____
DBSS ANS Load % ______10_____
DBSS Deflt load% ____40______
DBSS Peak load% ___60______
DBSS Full load% ____80______
DBSS Overload% ____125_____
Offset adjust __________ DI
Diss板和Dbss板之通讯故障。
|
|
| |
